Part of our vast range of Spares/Replacements available on our website. These Infra-Red Heat Bulbs are used on our Route Stand/Hot Rack, held in place by our Infra-Red Lamp Holders in and shielded by our Infra-Red Reflectors to prevent damage to the unit and wires. See the quantity discounts section for huge savings! These are non-jacketed, push in and 300w low pressure. The lamp is supplied in a protective sleeve, and should not be touched by hand. These are the only Heat Bulbs that are compatible with our Route Stands. Using any other Heat Bulbs may cause permanent damage to your Route Stand. These should be replaced at regular intervals to...

Part of our vast range of Spares/Replacements available on our website. These Infra-Red Lamp/Bulb Holders are used to connect and hold the Infra-Red Heat Bulbs in place on our Route Stand/Hot Rack. These should be fitted with our Infra-Red Reflectors, which are used to shield the heat from the bulbs to prevent damage to the Route Stand and wires. See the quantity discounts section for huge savings! These are the only Lamp Holders that are compatible with our Route Stands. Using any other holders may cause permanent damage to your Route Stand. Non-jacketed Lamp Holder, complete with fly heads and pre-cut additional cable...

Part of our vast range of Spares/Replacements available on our website. These Infra-Red Reflectors are used on our Route Stand/Hot Rack to sit the Infra-Red Lamp Holders in and to shield the heat from the Infra-Red Bulbs to prevent damage to the unit and wires. See the quantity discounts section for huge savings! These are the only Reflectors that are compatible with our Route Stands. Using any other Reflectors may cause permanent damage to your Route Stand. These should be replaced at regular intervals to maximise the efficiency of the Route Stand.

Icon Ceramic Terminal Blocks to suit our Route Stand/Hot Rack, can be purchased as spares/replacements in large quantities for large discounts. Located in the canopy of the Route Stand, easy-replacement. Ceramic body, perfect for use in high temperature environments. Used for two-way wire to wire connections.

Part of our vast range of Spares/Replacements available on our website. Our Rocker Switches are used to operate each level of heat on our Route Stand/Hot Rack. This means that unused levels can be switched off to save power and the extend the lifespan of the Route Stand. These are the only approved switches for our Route Stand. Using any other switches may cause permanent damage to your Route Stand. Easy fitment - simply disconnect wires to old switch and rewire to new one. These are located in the Route Stand switch box.

Heatproof Cable available as spare or replacement for Icon Engineering Triple Route Stands / Hot Racks. Purchase price is for 13 linear metres. Located in the canopy of the Route Stand. 8mtr required for complete rebuild of 3-Tier Route Stand. Sold as a 13mtr length. You can also purchase a 8mtr length of cable for our 2-Tier Route Stand / Hot Racks. Not using this cabling could cause permanent damage to the route stand.

Part of our vast range of Taps & Valves available on our website. The Icon Knee-Lever Valve is sold as a spare/replacement for our Knee-Lever Sinks. Manufactured from high-quality 304 grade stainless steel. Excellent durability and rust resistance. Easy-fitting, simply disconnect the old valve, attach the new valve to the bracket on the sink and connect to the Knee-Lever Hose. The small push buttons are not sold separately, a full replacement valve must be purchased. Part of our range of Sink Taps & Valves available on our website. Other Sinks Available on our Website Hand-Washing Sinks Catering Sinks Knee-Operated Sinks Infrared Sensor Tap Sinks Utility Sinks...

Part of our vast range of Taps & Valves available on our website. The Icon Knee-Lever Spout is sold as a spare/replacement for our Knee-Operated Sinks. Manufactured from quality 304 grade stainless steel for excellent durability. Easy-fitting, simply disconnect the old spout and attach the new one to the rear of the sink and screw into the Knee-Lever Hose. Other Sinks Available on our Website Hand-Washing Sinks Catering Sinks Knee-Operated Sinks Infrared Sensor Tap Sinks Utility Sinks Mop Sinks Sink Taps & Valves

Icon Utensil Holder, designed to slot in place on our Cut Table to hold utensils for cutting and boxing pizzas and other food in takeaway outlets. Manufactured from 304 grade stainless steel.

Stainless steel perforated standpipe waste with plastic inner for standard Icon Catering Sinks.  Acts as a plug, strainer and overflow. Available in 250mm long & 300mm long to suit sink depth. Complete with drain to suit 1.5" BSP angled European waste hole. High quality durable design.

Part of our range of Catering Spares, our Double Deck Mounted Pre-Rinse Unit is designed to be fitted on all of our Catering Sinks. This can be sold as an add-on part, or as a spare/replacement. General specification as listed below: - 8" Spout & valve can be included from the drop-down menu. (We also offer 6", 10" & 12" versions of this spout). Deck-mounted tap base with hot & cold levers. (We also offer a wall-mounted version of this unit). Rear wall bracket for stability & spring to keep hose rigid. Flexible hose & spray gun for ease of use....

Part of our range of Catering Spares, our Pre-Rinse Spray Gun is a sold as a replacement/spare for our Pre-Rinse Unit which can be mounted on all of our Catering Sinks. General specification as per the listed criteria: - WRAS approved. Easy installation, simply remove old spray gun from the end of the pre-rinse hose and attach the new one.